• LC100-A Digital Inductance Capacitance L/C Meter

  • Free Shipping ( from China ) PRODUCT ID: ADM006
  • USD



  • QTY
-+    可购数量:199
Buy It Now
Add to Cart


ICSH014A is a Capacitance, Inductance measuring module.

Engaged in the development of electronic engineers often need to measure inductance and capacitance, and inductance capacitance meter sold on the market price is higher, and the measurement of small capacitance inductance and small error, this instrument based on LC resonant principle, join the accurate measurement of high-speed micro controller calculation, small capacitance can be measured the inductance 1uH and less than 1pF, the maximum this is also the characteristics of the instrument, particularly suitable for microwave production and switching power supply transformer, inductance measurement.

ICSH014A (LC module) has four measuring mode:
1. C mode...... Capacitance (0.01pF-10uF).
2. L mode...... Inductance (0.001uH-100mH).
3. HL mode...... Large inductance (0.001mH-100H)
4. HC mode...... Large capacitance (1uF-100mF)

All stalls are automatic range, the use is very convenient. In this way, ICSH014A Whether from the measurement range and measurement precision can completely replace any kind of inductance and capacitance measuring instrument on the market, the performance parameters to the digital bridge, is a highly cost-effective instrument.

Introduction of structure

The overall effect diagram . When in use, you can use the Micro USB connection line is connected to the computer USB testing instrument power supply, if the user has a mobile phone charger with USB or with 5V power adapter with DC plug can also be directly to the instrument power supply. Special note: if you are using DC plug adapter, polar please hole positive confirmation, peripheral negative, while the Micro USB interface does not occur polarity error conditions.

The structure of the instrument

The button has a total of 5, "Reset" to 0 "HC" button, large capacitance, inductance, select "HL" option, "L/C" and black expansion function button. The HC, HL and L/C selection is self lock , a press release was 1, 0, and X represents the arbitrary function, see the table below:

Instructions for use

1. Connecting computer USB as the tester and switch on the power supply.

2. According to the element to be tested for the selection of mode, to choose to measure inductance Lx, capacitance Cx, inductance or capacitance HC HL, in measuring terminal open state from the screen to see:

Inductance:                 Measure Lx     0.000uH
The capacitive display:     Measure Cx     0.00pF
Large inductance shows:     Measure HL     0.000mH
Large capacitor shows:     Measure HL    0.00uF

3. Because of the measurement principle of the HC file is different, first stated the following Lx, Cx and HL three mode of operation:

In the three mode , the measurements are required for zero adjustment. The methods according to different inductance, capacitance .

Cx mode in terminal open state, press "Reset" key, the screen shows "Setting... OK "after the release, the screen time line should display" 0.00pF "; HL and Lx mode, the terminal short-circuit condition, press" Reset "key, the screen shows" Setting... OK "after the release, the screen time should show" 0.000mH "and" 0.000uH ", after the open circuit terminal for display" Over Range!". Then, you can put the inductance connected test instrument to test.
In the measuring result displayed, press the function keys are black, will display the test frequency current.

4. In the HC file, please make sure the capacitor is fully discharge to be measured, and then the red test clamp capacitor cathode, black test clamp capacitor anode, read the test results from the display screen and can, need to pay attention to is, the measurement of large capacity (more than 10mF), the test time can be more than 1 seconds, the test time of capacitor the longer the 100mF, about 7-8 seconds before the results.


Copyright © 2016 Adeept.com All Rights Reserved.